Abstract: New formulations and solutions to problems of optimization of a variable thermal conductivity coefficient for an inhomogeneous pipe and a flat wall with mixed boundary conditions are presented. The quality functionals are either the average temperature or the maximum temperature, and as a limitation - either the condition of constancy of the integral thermal conductivity coefficient, or a priori information about the change in the thermal conductivity coefficient in a known range. To solve problems for a pipe, two optimization methods are used: 1) a variational approach based on the introduction of conjugate functions and the construction of an extended Lagrange functional; 2) Pontryagin’s maximum principle. To solve the optimization problem for a flat wall under the assumption of weak material inhomogeneity, the expansion method in terms of a small physical parameter is used. As the fourth problem, optimization of the variable thermal conductivity coefficient of a non-uniform flat wall with boundary conditions of the first kind is considered. The solution to a singular optimization problem is found among broken extremals. Using specific examples, a comparison was made of the values of minimized functionals for bodies with a constant thermal conductivity coefficient and an optimal variable coefficient. The gain from optimization is estimated.
Keywords: optimization, thermal conductivity coefficient, functionally graded material, flat wall, pipe, Lagrange variational method, Pontryagin's maximum principle, small parameter expansion method, singular problem
For citation: Vatulyan, A. O. and Nesterov, S. À. Some Analytical Solutions in Problems of Optimization of Variable Thermal Conductivity Coefficient,
Vladikavkaz Math. J., 2024, vol. 26, no. 3, pp. 33-46 (in Russian).
DOI 10.46698/v9056-4395-2233-f
1. Lee, W. Y., Stinton, D. P., Bernardt, C. C., Erdogan, F, Lee, Y. D. and Mutasin, Z. Concept of Functionally Graded Materials for Advanced Thermal Barrier Coatings Applications, Journal of American Ceramic Society, 1996, vol. 19, pp. 3003-3012. DOI: 10.1111/j.1151-2916.1996.tb08070.x.
2. Wetherhold, R. C., Seelman, S. and Wang, J. The Use of Functionally Graded Materials
to Eliminated or Control Thermal Deformation, Composites Science and Technology, 1996, no. 56,
pp. 1099-1104. DOI: 10.1016/0266-3538(96)00075-9.
3. Mathew, J. and Krishnan, S. A Review on Transient Thermal Management of Electronic Devices,
Journal of Electronic Packaging, 2022, vol. 144(1), DOI: 10.1115/1.4050002.
4. Bejan, A. Constructal-Theory Network of Conducting Paths for Cooling a Heat Generating Volume,
International Journal of Heat and Mass Transfer, 1997, vol. 40, no. 4, pp. 799-816. DOI: 10.1016/0017-9310(96)00175-5.
5. Hua, Y.-C., Zhao, T. and Guo, Z.-Y. Transient Thermal Conduction Optimization for Solid Sensible Heat Thermal Energy Storage Modules by the Monte Carlo Method, Energy, 2017, vol. 133, pp. 338-347. DOI: 10.1016/j.energy.2017.05.073.
6. Chen, K., Wang, S. and Song, M. Optimization of Heat Source Distribution for Two-Dimensional
Heat Conduction Using Bionic Method, International Journal of Heat and Mass Transfer,
2016, vol. 93, pp. 108-117.
7. Birman, V. and Byrd, L. W. Modeling and Analysis of Functionally Graded Materials and Structures,
Applied Mechanics Reviews, 2007, vol. 60, no. 5, pp. 195-216. DOI: 10.1115/1.2777164.
8. Suresh, S. and Mortensen, A. Fundamentals of Functionally Graded Materials,
London, Cambridge Publication, 1998, 165 p. DOI: 10.1016/S1369-7021(98)80023.
9. Bykov Yu. V., Egorov S. V., Eremeev A. G. and at all. Fabrication of Metal-Ceramic
Functionally Graded Materials by Microwave Sintering, Fizika i khimiya obrabotki materialov
[Physics and Chemistry of Materials Treatment], 2011, no. 4, pp. 52-61 (in Russian).
10. Gururaja, U., Shrikantha, R. S. and Gangadharan, K. V. Functionally Graded Composite
Materials: An Overview, Procedia Matherials Science, 2014, vol. 5, pp. 1291-1299. DOI: 10.1016/j.mspro.2014.07.442.
11. Dirker, J. and Meyer, J. P. Topology Optimization for an Internal Heat-Conduction Cooling
Scheme in a Square Domain for High Heat Flux Applications, Journal of Heat Transfer, 2013,
vol. 135(11). DOI: 10.1115/1.4024615.
12. Cheng, C. H. and Chen, Y. F. Topology Optimization of Heat Conduction Paths by
a Non-Constrained Volume-of-Solid Function Method, International Journal of Thermal Sciences,
2014, vol. 78, pp. 16-25. DOI: 10.1016/j.ijthermalsci.2013.11.011.
13. Dede, E. M., Joshi, S. N. and Zhou, F. Topology Optimization, Additive Layer Manufacturing,
and Experimental Testing of an Air-Cooled Heat Sink, Journal of Mechanical Design, 2015,
vol. 137(11). DOI: 10.1115/1.4030989.
14. Gersborg-Hansen, A., Bendsoe, M. P. and Sigmund, O. Topology Optimization of Heat Conduction
Problems Using the Finite Volume Method, Structural and Multidisciplinary Optimization, 2006,
vol. 31(4), pp. 251-259. DOI: 10.1007/s00158-005-0584-3.
15. Dbouk, T. A Review About the Engineering Design of Optimal Heat Transfer Systems Using Topology Optimization,
Applied Thermal Engineering, 2017, vol. 112, pp. 841-854. DOI: 10.1016/j.applthermaleng.2016.10.134.
16. Yongcun, Z., Shutian, L. and Heting, Q. Design of the Heat Conduction Structure Based
on the Topology Optimization, Developments in Heat Transfer, Dr. Marco Aurelio Dos Santos Bernardes (Ed.),
2011, pp. 523-536. DOI: 10.5772/20060.
17. Banichuk, N. V. Vvedeniye v optimizatsiyu konstruktsiy [Introduction to Optimization of Structures],
Moscow, Nauka, 1986, 304 p. (in Russian).
18. Tong, Z.-X., Li, M.-J., Yan, J.-J. and Tao, W.-Q. Optimizing Thermal Conductivity Distribution for Heat Conduction Problems with Different Optimization Objectives, International Journal of Heat and Mass Transfer, 2018, vol. 119, pp. 343-354. DOI: 10.1016/j.ijheatmasstransfer.2017.11.108.
19. Bràtus, À. Ñ. and Kartvelishvili, V. Ì. Approximate Analitycal Solutions in Problems
of Optimizing Stability and Vibration Frequencies of Elastic Thin-Walled Structure,
Izvestiya AN SSSR. Mekhanika tverdogo tela, 1981, no. 6, p. 119-139 (in Russian).
20. Sarkisyan, V. S., Gukasyan, G. M. and Grigoryan, A. A. Optimal Design of a Circular Plate
with Rectilinear Anisotropy, Journal of Mathematical Sciences, 2001, vol. 104, p. 1569-1574.
DOI: 10.1023/A:1011300122949.
21. Sarkisyan, V. S. Nekotoryye zadachi matematicheskoy teorii uprugosti anizotropnogo tela
[Some Problems of the Mathematical Theory of Elasticity of an Anisotropic Body],
Yerevan, YerSU Publishing House, 1976, 536 p. (in Russian).
22. Pontryagin, L. S., Boltyanskii, V. G., Gamkrelidze, R. V. and Mishchenko E. F. The Mathematical Theory of Optimal Processes, New York, Interscience Publishers, 1962, 376 p.
23. Warner, W. H. Optimal Design Problems for Elastic Bodies by Use of the Maximum Principle,
Journal of Elasticity, 2000, vol. 59, pp. 357-367. DOI: 10.1023/A:1011055305523.
24. Alekhin, V. V. Design of a Cross-Laminated Cantilever of Minimum Mass with a Limitation
on Maximum Deflection, Applied Mechanics and Technical Physics, 2007, vol. 48, no. 4, p. 104-110 (in Russian).
25. Vatulyan, A. O. and Nesterov, S. A. Koeffitsiyentnyye obratnyye zadachi termomekhaniki
[Coefficient Inverse Problems of Thermomechanics. 2nd ed.],
Rostov-on-Don, Taganrog, Southern Federal University Press, 2022, 178 p. (in Russian).
26. Meric, R. A. Optimization of thermal Conductivity Coefficients of Isotropic and Orthotropic Bodies,
Heat Transfer, 1985, no. 3, pp. 1-6 (in Russian).
27. Meric, R. A. Material and Load Optimization by the Adjoint Variable Method,
Trans. ASME. Journal of Heat Transfer, 1987, vol. 109, no. 3, pp. 782-784.
28. Tian, Z., Xuan, W. and Zeng-Yuan G. Optimal Thermal Conductivity Design for the Volume-to-Point
Heat Conduction Problem Based on Adjoint Analysis, Case Studies in Thermal Engineering, 2022,
vol. 40, pp. 1-16. DOI: 10.1016/j.csite.2022.102471.
29. Ito, K. and Kunisch, K. Lagrange Multiplier Approach To Variational Problems and Applications,
SIAM, 2008, 341 p. DOI: 10.2307/40590422.
30. Nedin, R., Nesterov S. and Vatulyan, A. On Reconstruction of Thermalphysic Characteristics
of Functionally Graded Hollow Cylinder, Applied Mathematical Modelling, 2016, vol. 40,
no. 4, pp. 2711-2719. DOI: 10.1016/j.apm.2015.09.078.